Sunday, January 15, 2012

Irritated, Flaky Or Scaly Scalp? Try These Soothing, Healing Ideas

!#8# Irritated, Flaky Or Scaly Scalp? Try These Soothing, Healing Ideas

Ever since I was old enough to notice, I've had problems on and off with dandruff and scalp irritation. I'm honestly not even sure what the actual name is for what I have, because I believe it's almost like a mix between psoriasis and dandruff, since it alternates with white scabs and scales and large flakes of scalp coming off.

Another thing I can tell you is that it gets exponentially worse during times of intense stress, which others can also attest to, since we do tend to express our emotions outwardly when it comes to our scalp and our skin, some more so than others.

There are a lot of people who suffer from severe flaking, itching and irritation of the scalp, and most of them will tell you that it gets much worse when they are either in different climates, or have a lot of stress going on in their lives.

So, what can you do to soothe and repair your scalp? Well, there are several techniques that I have found work well for me personally, and I'm going to share those here, and there are also some treatments and techniques that I have not tried that I've read about which we'll talk about as well.

One thing that I already talked about which may have a huge impact on the health and comfort of your scalp condition is climate. By that I don't mean strictly temperature, but really the level of humidity that is in the air. I notice that during the dry winter months my scalp tends to get very irritated quickly, especially if I'm on vacation somewhere that the indoor heated air is extremely desert-like.

Getting a humidifier in your home may greatly help the condition of your scalp if you live in arid climates or if, like me, you live in a region where the winter season is extremely punishing to the scalp and the skin, not to mention the lungs.

There are quite a few high tech humidifiers these days that are easy to clean and offer pure, cleansed air that is moisturizing and soothing rather than drying. Some people these days even have whole-home humidifiers that work with their furnace to crank out extra humidity during the dry months, to help reduce the effect of the drying heat on the lungs and skin, and make the air easier for you and your body to process.

A crucial part of maintaining the health of your scalp, and helping to keep the critical moisture sealed in to avoid flaking off, itching and scabbing over, is to choose a good shampoo. Never choose one that is for oily hair, or says that it creates body, but rather, always go for one that is super-emollient. You may want to look for ingredients in your shampoo such as olive oil, macademia nut oil, camphor oil, and other nourishing oils.

Stay away from shampoos that have a lot of alcohol in them. One of the best shampoos for my scalp and hair I've found is Nexxus Therappe extra moisturizing shampoo, and the best medicated one that I've found is Selsun Blue moisturizing shampoo, both of which not only nourish the scalp, but also which leave your hair silky and bouncy.

I try not to use a medicated dandruff shampoo every time, but rather I alternate my shampoos between medicated and non-medicated moisturizing shampoos, so that my scalp doesn't develop a sort of resistance to the medicated tar shampoo.

If you dye your hair, make sure you rub some sort of protectant on your scalp, especially the areas that tend to get the most irritated, before you get your hair dyed or do the job yourself. You can use a petroleum jelly, or if you know of some other recommendation, use that to protect your scalp from the harsh chemicals. The same goes for any type of harsh chemical treatment, and you should always ask your stylist how she can help protect your scalp from damage and drying.

Try a scalp treatment. There are many good natural scalp treatments that use soothing, organic and nutritive ingredients in them, that can be applied to the scalp and left on all night. These types of scalp treatments can help repair scalp damage, as well as unclog the follicles and dislodge any leftover styling gunk or other irritants that have been left behind, leaving your scalp feeling superb.

The biggest tip I can share with you to help get your scalp healthy and keep it that way is to stop touching it. I know that it's tempting for us to "pick" at our scalps, especially if you're prone to getting scabs or scales on the scalp, but doing so only prolongs the problem.

You can end up with a bleeding scalp, and you will also make it harder for the scalp to heal when you consistently keep tearing open the wounds that are already there. Do whatever you have to do to keep your fingers from creeping up to your head, it's crucial to the health and well being of your scalp.

If you follow these simple techniques, you should notice a significant improvement in your scalp, and hence will also see your hair improve. Since you have to possess a healthy scalp to also have healthy, shiny hair, you'll notice that once your scalp problems are resolved, you hair will follow suit.


Irritated, Flaky Or Scaly Scalp? Try These Soothing, Healing Ideas

Good Bargain Pancake Recipe Bisquick

Thursday, December 22, 2011

The Modern Furnace Sequence of Operation - Trying To Diagnose A Problem With Your Furnace?

!±8± The Modern Furnace Sequence of Operation - Trying To Diagnose A Problem With Your Furnace?

Before we begin, we must say only qualified persons should attempt working on a gas furnace. Please consult a professional service company for repairs or for correct diagnosing!

Remember when furnaces were pretty simple? There was a pilot and a thermocouple, a couple of safety controls, a blower assembly, a set of burners and of course the heat exchanger. The down side of these old furnaces was the cost to operate them as they were usually about 50% efficient. The modern furnaces of today run between 80% and 95% efficient.

We will talk about the typical 80% single stage heating gas furnace in this article as this is the most common out there these days.

On a signal from the room thermostat that heating is needed, the first thing that takes place is the draft inducer begins running and creating a draft in the heat exchanger. If there is no obstruction in the flue pipe of the furnace, the inducer will send a small pressure to the pressure switch via a small rubber tube, obviously, this tubing must be free of debris or any cracks. If there is sufficient draft, this will close contacts inside the pressure switch. The pressure switch then sends a signal down to the control board which is usually mounted in the blower section. There are various safety controls such as, but not limited to, over temperature limit switches, plenum thermostats, flame sensors, and roll out switches that must be closed, but if they are and the control board is good, a signal will be sent to the ignition device. There are many ignition systems used including intermittent spark ignition, direct spark ignition, hot surface ignition, electronic ignition, standing pilots and others. MOST furnaces at this time use hot surface ignition with a flame sensor. So we will concentrate this article on the hot surface ignition system that uses a flame sensor.

There are several different types of hot surface ignitors on the market. The most common is the Silicone Carbide type which is VERY brittle and breaks easily. Do not handle this type by the carbide section as the oil from your hands will shorten the life span. This type has a life expectancy of 3-5 years usually. There are flat ones and round spiral versions of these.

The next type is the Silicone Nitride which will last much longer and do not break easily, some of them are meant for 24 volt systems as in the Honeywell Smart Valve systems, and Trane 80 volt systems.

There are also older systems that use a hot surface ignitor that doesn't use a separate flame sensor but rather once they glow orange then switch over to sense the flame. These systems are called radiant systems and have been proven unreliable and sometimes unsafe as they are not sensing a flame on all burners, only the one the ignitor is mounted on. Most furnace manufacturers are requiring you to add a flame sensor when you change a control board.

Assuming the control board "sees" all the safety controls are closed and it has a signal from the pressure switch, it will then send 120 volts to the hot surface ignitor which is usually mounted on the right side of the burners. (Be aware that some ignition systems use 24 volts for lighting a pilot and Trane and some others use a 80 volt Silicone Nitride system on SOME of their models). Once the hot surface ignitor glows orange you should hear a click which is the gas valve opening to let gas flow to the burners. This should give almost instant ignition on all burners. The flame sensor is a small white ceramic electrode mounted on the left side of the burners. It's job is to "sense" a flame on the burner which is at the opposite side of the furnace from the hot surface ignitor. If it doesn't get a flame within about 10-15 seconds, it will shut the burners back off for safety. Usually if a furnace goes through (3) cycles like this, it will go into lock out. To get it out of lock out you will need to shut the power to the furnace off and back on. Flame sensors should be cleaned with sandpaper once a year as part of maintenance.

Once all the burners are lit and running, the control board will send a signal to the blower motor to start.

Be advised however, there are MANY control boards including intergrated control boards where all functions of the furnace are controlled by this board, also out there are ignition modules used for ignition only and a separate fan timer control board that only starts and stops the blower motor as well as monitoring safety controls.

Before you even THINK about working on your furnace, please remember this is a possible lethal piece of equipment which takes a great deal of training for a service person to work on. Folks may want to save money by doing their own work, but there is much to be said about a proper diagnoses by a reputable company let alone any dangers to bodily harm from inexperienced people working on this equipment. If in doubt "DON"T DO IT"


The Modern Furnace Sequence of Operation - Trying To Diagnose A Problem With Your Furnace?

Price Fender Stratosonic Comparison Canon 60d Last Minute Elliptical Stepper Machine

Friday, December 2, 2011

Honeywell HE220A Whole House Bypass Humidifier

!±8±Honeywell HE220A Whole House Bypass Humidifier

Brand : Honeywell
Rate :
Price : $99.86
Post Date : Dec 02, 2011 02:19:40
Usually ships in 24 hours



This flow-thru by-pass whole house humidification unit is low maintenance, cost effective, and is simple to operate. This unit requires good access to a return duct and drain. The humidifier mounts on supply plenum or return. By-pass carries air from supply, through humidifier, to return. Standard control. No. HE220A1019: 12 gallon per day, uses Vista model No. 710 filter No. HE260A1010: 17 gallon per day, uses Vista model No. 714 filter

Prices Sleep Innovations Mattress Review Spyderco Dragonfly Grand Sale Good Hamilton Beach Can Opener


Twitter Facebook Flickr RSS



Français Deutsch Italiano Português
Español 日本語 한국의 中国简体。







Sponsor Links